Servo Motor Noise: What to Specify Before Ordering
Jiangnan Electric
If noise matters to your machine, raise it when discussing the motor specification with Jiangnan Electric. An energized servo axis can be audible while holding position as well as while moving. [3] For equipment located close to an operator, include both states in the brief whenever they occur in normal use.
Identify the motor and drive together
Our 40A model SF40A01030C2014 is listed in the catalog with 0.1 kW (100 W) rated output, 0.32 N·m rated torque and a rated speed of 3,000 rpm. [1][2]
For a project considering this motor, identify the proposed servo drive, feedback configuration and mounting arrangement. The controls and mechanics of a servo axis can affect its audible behavior. [3] Keep those details with any noise test result so the result can be traced to a particular setup.
The 40A specification table provides the motor ratings for selection. A noise target for your machine needs a separate acceptance method, agreed for the intended assembly and operating conditions.
Describe the cycle, including the pauses
Explain how far the axis moves, how quickly it starts and stops, whether it reverses, and how long it holds position with the drive enabled. Add the normal load and any other operating modes covered by the noise requirement.
Consider a slide that advances a part, waits beside an operator, then returns. A useful evaluation would include the travel and the energized waiting period. If a brief event such as a reversal has its own acceptance requirement, state that separately. This gives everyone the same sequence to evaluate.
Put a measurement method beside the number
Before comparing decibel figures, confirm whether each is a sound pressure level or a sound power level. These are different quantities. Sound pressure readings depend on the measurement location and acoustic environment. Sound power describes the acoustic output of the source under the stated operating conditions. [4]
For a sound pressure requirement, specify the microphone position, test environment, operating sequence and measurement method. Agree whether the result represents a time-averaged sound level over a defined period or a maximum during a particular event. Include how background noise will be assessed. A number with these conditions attached is much more useful for comparing samples.
Define what the sample evaluation covers
Agree whether you are evaluating a motor and drive, an assembled axis or the complete machine. A motor test and a complete-machine test answer different questions. If the requirement concerns noise at the operator's position, plan verification on the finished machine under the agreed conditions.
Record the drive settings and motion sequence used for the accepted result. When evaluating a quieter setting, also check that the axis still meets its positioning, load and cycle-time requirements. Any later change to the drive, mounting or motion profile should prompt a review of whether the noise evaluation still represents the machine.
To discuss a 40A motor for your project, send Jiangnan Electric the required motion and load, proposed drive, mounting drawing and noise acceptance criteria. Tell us where the motor will sit in the machine and which operating periods matter most. We can then review the motor configuration against a clearly defined application.
References
[1] Jiangnan Electric / Zhongke Servo. English Servo Motor Catalog.
Company-supplied catalog, PDF page 22 (printed page 13): 40A technical specifications, including SF40A01030C2014. Product data in this article follows the supplied catalog.
[2] Hangzhou Jiangnan Electric Motor Co., Ltd.. A Series 40 Frame Permanent Magnet Servo Motors.
Company product page identifying the 40A range and the configuration used in this article.
https://www.jnelectricmotor.com/servo-electric-motors/low-inertia-servo-motor/a-b-series-40-frame-permanent-magnet-servo.html
[3] Performance Motion Devices. Servo Motor Noise.
Technical background on audible noise during motion and position holding, and the influence of servo controls and mechanical behavior. No drive settings or tuning instructions are adopted here.
https://www.pmdcorp.com/resources/type/articles/servo-motor-noise-and-how-to-fix
[4] Brüel & Kjær. Introduction to Noise Measurements on Business Machines.
Application note BO 0125, printed pages 2–3: sound pressure and sound power, and the influence of measurement position and acoustic environment. Used for basic acoustics only; the document's business-machine standards are not applied to Jiangnan motors.
https://www.bksv.com/media/doc/bo0125.pdf
Disclaimer
The information in this article is provided for general reference only. Product specifications, performance, configuration options and suitability must be evaluated in detail for the intended application and actual operating conditions. Before selecting, purchasing or using a product, please confirm the relevant details with Jiangnan Electric and refer to the applicable technical documentation and agreed specifications. This article does not replace product-specific instructions or a professional engineering assessment.
