How to Install a Permanent Magnet Synchronous Motor (PMSM)
Installing a permanent magnet synchronous motor is more than simply mounting the motor and connecting cables.
In most industrial applications, a PMSM operates together with a frequency converter or another electronic drive. Mechanical installation, motor data and drive compatibility therefore need to be checked before the machine is started.
For equipment manufacturers and industrial users, the following checks cover the most important parts of a typical PMSM installation without going too deeply into motor theory.
Check the Motor Before Installation
Start with the motor nameplate and technical drawing.
Confirm that the motor supplied matches the application in terms of rated power, voltage, current, speed, torque, mounting arrangement, cooling method and protection level.
This is particularly important when replacing an existing motor.
Two motors with the same rated power can have very different speed and torque characteristics. A 45 kW high-speed motor, for example, is not mechanically equivalent to a 45 kW low-speed, high-torque motor.
Before installation, also inspect the housing, shaft, mounting surfaces and terminal area for visible shipping damage.
If the motor has been stored for a long period, the electrical condition and bearings may require additional inspection before use.
Check the Installation Environment
The operating environment should match the motor specification.
Temperature, humidity, dust, moisture and altitude can all affect motor operation.
For air-cooled motors, enough space should be left around the housing and ventilation path. Blocking the cooling surfaces can increase motor temperature even when the electrical load is normal.
The specified IP rating should also be considered together with the complete installation. Cable entries, terminal-box sealing and the surrounding machine structure all influence the final protection of the system.
Mount the Motor Correctly
The supporting structure should be flat, stable and sufficiently rigid.
Depending on the motor design, the installation may use foot mounting, flange mounting, direct mounting or a customized mechanical interface.
Mounting bolts should be tightened evenly. They should not be used to pull a misaligned motor into position.
For directly coupled equipment, check both angular and parallel shaft alignment.
Poor alignment can increase vibration and place additional load on bearings, couplings and shafts.
Where belts and pulleys are used, pulley alignment and belt tension should also be checked. Excessive belt tension can shorten bearing life.
Confirm the Motor and Drive Match
Most industrial PMSMs should be treated as part of a complete drive system.
Before wiring, confirm that the frequency converter or servo drive supports the selected motor.
Important information may include rated voltage, rated current, rated speed, motor pole information, control mode and any temperature or feedback devices installed on the motor.
The controller parameters must correspond to the actual motor.
For replacement projects, do not assume that the settings used for the previous motor can be copied directly to the new one.
Follow the Actual Wiring Diagram
A PMSM should be wired according to the documentation supplied with the actual motor and drive.
The protective earth connection must be correctly installed.
In a typical variable-speed system, the incoming electrical supply is connected to the drive, while the drive output is connected to the motor phases. Additional components such as reactors, filters, braking units or sensors depend on the specific system.
There is no universal wiring diagram that applies to every PMSM.
For this reason, copying a terminal arrangement from another motor - even one with the same voltage - is not recommended.


Jiangnan Electric PMSM Options
Hangzhou Jiangnan Electric Motor Co., Ltd. manufactures permanent magnet motors for a range of industrial applications.
Its PMSM portfolio includes industrial permanent magnet synchronous motors and axial-flux permanent magnet motor solutions for different speed, torque and installation requirements.
For OEM and motor-replacement projects, parameters such as shaft dimensions, mounting arrangement, rated speed, torque, cooling and drive requirements can be reviewed together rather than selecting the motor from power rating alone.
Providing an existing motor nameplate and mechanical drawing usually makes this process considerably faster.
Before the First Start
Before starting the motor, confirm that the mounting is secure, the shaft is correctly aligned, wiring follows the supplied diagram, protective grounding is complete and the drive parameters correspond to the motor.
Also make sure the driven machine is ready to rotate and that no tools or temporary installation materials remain around moving components.
A correct installation provides the foundation for reliable commissioning.
The next step is not simply to switch the motor on at full load, but to verify rotation, drive settings and operating conditions in a controlled way.
About Jiangnan Electric
Hangzhou Jiangnan Electric Motor Co., Ltd. develops and manufactures electric motors for industrial equipment and smart-home applications. For product information and OEM inquiries, visit www.jnelectricmotor.com
Disclaimer
The information in this article is provided for general reference only. Product specifications, performance, configuration options and suitability must be evaluated in detail for the intended application and actual operating conditions. Before selecting, purchasing or using a product, please confirm the relevant details with Jiangnan Electric and refer to the applicable technical documentation and agreed specifications. This article does not replace product-specific instructions or a professional engineering assessment.
