How to Commission and Maintain a PMSM After Installation
A permanent magnet synchronous motor can be installed correctly and still perform poorly if the drive parameters, rotation direction or mechanical load are not properly checked.
Commissioning is the stage where the motor, drive and driven machine are verified as one working system.
For industrial users, the objective is simple: confirm that the motor starts correctly, reaches the required operating condition and remains stable under the actual load.
Check the Drive Parameters First
Before starting the motor, confirm that the controller contains the correct motor data.
Depending on the drive system, this may include rated current, rated speed, pole information, acceleration and deceleration settings and other motor-specific parameters.
In Jiangnan Electric's pumping-unit drive documentation, motor parameters are normally configured during system commissioning and should not be changed without a specific reason or confirmation.
For factory-matched motor and drive systems, unnecessary parameter changes can create problems that were not present in the original configuration.
Verify Rotation Before Full Operation
Before applying normal load, confirm the required direction of rotation.
This is particularly important for fans, pumps, conveyors and direct-drive machinery.
The test should be carried out according to the motor and drive instructions and with the surrounding machine in a safe condition.
If rotation is incorrect, correct it using the method specified for the actual drive system rather than experimenting with wiring or parameters.
Monitor the First Run
A successful first start involves more than checking whether the shaft turns.
During initial operation, observe motor current, speed, vibration, noise and temperature.
The drive should also be checked for alarms or warnings.
If the motor develops abnormal vibration, unexpected noise or rapidly increasing temperature, stop the system and identify the cause before continuing.
The problem may not necessarily be inside the motor. Possible causes include poor alignment, loose mounting, incorrect drive settings, excessive mechanical load or a problem in the driven equipment.
Test Under the Real Load
A no-load test is useful, but it does not represent the final operating condition.
Once basic operation has been verified, gradually bring the machine to its normal operating point and monitor the system again.
Variable-speed equipment should ideally be checked at several representative operating speeds.
This is especially important where the motor operates for extended periods at low speed and high torque, because motor cooling conditions can differ significantly from operation near rated speed.
The motor should therefore be evaluated according to its actual duty rather than rated power alone.

A Jiangnan Low-Speed, High-Torque Example
Jiangnan Electric's JNPM520-45 provides a useful example of why commissioning should follow the actual application.
The motor is part of an intelligent drive system developed for beam pumping equipment.
Its documented specifications include 45 kW rated power, 380 V supply, 245 rpm rated speed and 1754 N.m rated torque, together with horizontal mounting, natural cooling and IP55 protection.
This is very different from a conventional 45 kW high-speed industrial motor.
The low-speed, high-torque operating point means that the motor, drive parameters and mechanical connection to the pumping equipment must be considered together.
The corresponding product documentation therefore covers not only the motor but also the drive system, protection functions, parameter settings and startup process.
|
Commission the complete drive system, not just the motor. |
Jiangnan Electric also supplies other permanent magnet motor configurations, so the JNPM520-45 values should be treated as one application example rather than general specifications for all Jiangnan motors.
Basic Maintenance After Commissioning
Once the motor enters normal service, keep the motor and surrounding equipment clean and make sure cooling paths remain unobstructed.
Electrical cabinets should remain dry and adequately ventilated.
Changes in vibration or bearing noise should be investigated, particularly if they appear gradually after a period of operation.
If a protection device repeatedly trips, do not simply reset the system and continue running. The cause may be overload, incorrect settings, an electrical problem or an issue with the driven machine.
Keeping basic commissioning records - such as current, speed and temperature under normal load - can also provide a useful reference for later maintenance.
When Replacing an Existing PMSM
For a replacement project, the most useful information is usually the existing motor nameplate, mechanical drawing, rated speed, torque, shaft dimensions and drive model.
For direct-drive equipment, information about the mechanical load is also important.
Sending these details before ordering allows the motor manufacturer to check both mechanical and electrical compatibility and reduces the risk of modifications being required after delivery.
Reliable Operation Starts with Correct Commissioning
A PMSM is part of a complete motion or drive system.
Reliable operation depends on the motor, drive, wiring, cooling and mechanical load working together.
After installation, the practical commissioning sequence is to confirm the drive data, verify rotation, monitor the first run and then test the motor under its real operating load.
For new equipment and replacement projects, Jiangnan Electric can review existing motor specifications, drawings and drive information before recommending an appropriate PMSM configuration.
About Jiangnan Electric
Hangzhou Jiangnan Electric Motor Co., Ltd. develops and manufactures electric motors for industrial equipment and smart-home applications. For product information and OEM inquiries, visit www.jnelectricmotor.com
Disclaimer
The information in this article is provided for general reference only. Product specifications, performance, configuration options and suitability must be evaluated in detail for the intended application and actual operating conditions. Before selecting, purchasing or using a product, please confirm the relevant details with Jiangnan Electric and refer to the applicable technical documentation and agreed specifications. This article does not replace product-specific instructions or a professional engineering assessment.
