Compact Servo Motors: What a Shorter Body Changes
In the 400 W versions shown in our catalog, the 60C motor's nominal LL length is 14 mm shorter than the 60B's. Both have a 60 mm mounting flange. That difference can matter when a machine designer is working around a nearby panel or another axis. [1]
At Jiangnan Electric, we recommend treating the available installation space as part of the motor requirement from the beginning. A request for a compact servo motor becomes more useful when it identifies which dimension needs to change.
Two 400 W Configurations, Different Lengths
The comparison below uses the published 60B and 60C configurations without a holding brake. Our catalog places the C Series in the medium-inertia range and describes its short motor body for industrial and material-handling robots. Check the model drawing for actual dimensions. [1]
|
Catalog parameter |
60B, 400 W |
60C, 400 W |
|
Listed drive voltage |
48 V |
48 V |
|
Rated power |
0.4 kW |
0.4 kW |
|
Rated torque |
1.27 N·m |
1.27 N·m |
|
Rated speed |
3,000 rpm |
3,000 rpm |
|
Mounting flange size |
60 mm |
60 mm |
|
Motor length LL, no brake |
124 ± 1 mm |
110 ± 1 mm |
Source: Jiangnan / Zhongke Servo English catalog, PDF pages 29-30 and 37-38. Compared models: SF60B04030M2014 and SF60C04030M2014, both without a holding brake. LL is the motor-length dimension identified in the mounting drawings. [1]
The nominal difference is 14 mm, with each drawing retaining its stated tolerance. It is a comparison of one dimension, not a measurement of complete machine size, power density or efficiency.
Find the Dimension That Is Restricting the Layout
A shorter motor is useful only when it frees space in the direction the machine needs. If the obstruction is behind the motor, body length may be the relevant constraint. If it is beside a connector or at the shaft coupling, changing the body length may leave the problem unresolved.
Mark the available space from the mounting face and show the nearby components. Include the permitted width and height, not just the distance behind the flange. A simple section drawing can communicate this more clearly than a request for the smallest available motor.
Do Not Treat the Shorter Version as a Drop-In Replacement
The two configurations share the rated values shown above, but other catalog entries differ. Their published peak-torque and protection ratings are not the same. Matching power, rated torque and rated speed is therefore not enough to establish equivalent capability. [1]
The mounting drawings also show different fixing-hole details. Compare the locating diameter, hole positions, shaft dimensions and coupling arrangement before deciding whether a different motor can use the existing bracket. A shared 60 mm flange designation does not establish a complete mechanical match. [1]
Keep the required movement and load in the review. Solving an interference problem is only useful if the selected motor and compatible drive can also perform the intended job.

Allow Space Beyond the Motor Body
Our 60B and 60C drawings show the shaft, cable exits and connectors as well as the motor body. The LL value should be read with the whole drawing, rather than treated as the space required for the complete installation. Brake-equipped versions use separate length entries and must be checked separately. [1]
In the machine layout, reserve room for the actual cable route and the access needed to connect, fasten and remove the motor. Apply the cable supplier's bend-radius requirements. Do not solve a clearance issue on paper by drawing a cable bend that the specified cable cannot accommodate.
Check the proposed installation under its intended operating conditions, including the covers and surrounding components. A dimensional fit is one part of the review, not the final approval of the axis.
Show Us the Space You Need to Recover
For a compact-machine project, send Jiangnan Electric the available installation dimensions, mating-component drawing and required motor operating point. Include the drive model and the intended brake and feedback configuration. For a replacement, add the existing motor drawing and mark the interference you are trying to remove.
Our servo motor range is available for review on the Jiangnan Electric website. The C Series in the accompanying catalog offers a short-body option to discuss where the layout calls for it; the proposed configuration still needs technical confirmation for the application. [1][2]
The useful result is not simply a shorter motor. It is a motor that fits the available space, leaves the connections accessible and meets the machine's operating requirements. Those are the conditions to compare before changing the mounting arrangement.

References
[1] Jiangnan / Zhongke Servo. English Servo Motor Catalog. Company-supplied PDF.
File: 伺服电机宣传页(英文)(1).pdf. PDF pages 29-30 (printed pages 20-21): 60B ratings and mounting dimensions. PDF pages 36-38 (printed pages 27-29): C Series description, 60C ratings and mounting dimensions. PDF page 2: application-based selection support.
Product values in this article follow this supplied edition. No public download URL for the same edition was verified; request the current approved catalog and configuration drawing from Jiangnan Electric. Do not substitute figures from a different edition or product-family page.
[2] Hangzhou Jiangnan Electric Motor Co., Ltd. Servo Electric Motors.
www.jnelectricmotor.com/servo-electric-motors/
Disclaimer
The information in this article is provided for general reference only. Product specifications, performance, configuration options and suitability must be evaluated in detail for the intended application and actual operating conditions. Before selecting, purchasing or using a product, please confirm the relevant details with Jiangnan Electric and refer to the applicable technical documentation and agreed specifications. This article does not replace product-specific instructions or a professional engineering assessment.
